Tension Fabric Media Walls

Get a wall that photographs crease-free from every angle, because the frame holds the printed fabric drum-tight rather than relying on hooks, poppers or overlapping panels.

Talk to an expert
800+ Products available
50,000+ Orders
30+ Countries
22+ Years experience
Tension Fabric Media Walls
Hochwertiges gerades Spannstoff-Hintergrunddisplay

Hochwertiges gerades Spannstoff-Hintergrunddisplay

€292,95
Gebogene mobile Medienwand aus Spannstoff

Gebogene mobile Medienwand aus Spannstoff

€281,95
Tragbare gerade Spannstoff-Medienwand – quadratische Ecken

Tragbare gerade Spannstoff-Medienwand – quadratische Ecken

€292,95
EZ-Stoffbannerständer für Messedisplays

EZ-Stoffbannerständer für Messedisplays

€222,95
Tragbares 2.3m H hohes Stoff-Ausstellungsdisplay

Tragbares 2.3m H hohes Stoff-Ausstellungsdisplay

€246,95
Spannstoff-Step-and-Repeat-Displaywand

Spannstoff-Step-and-Repeat-Displaywand

€292,95
Hochwertige gerade Stoffwand mit LED-Strahlern

Hochwertige gerade Stoffwand mit LED-Strahlern

€337,95
Hochwertiges gebogenes Stoff-Rückwandset mit Klemmleuchten

Hochwertiges gebogenes Stoff-Rückwandset mit Klemmleuchten

€341,95

Not sure which display fits your booth?

Get a free 2D mockup with your artwork — see exactly how it looks before you order. 7,000+ happy exhibitors.

Talk to an expert
S-förmige Wellen-Ausstellungswand aus Stoff

S-förmige Wellen-Ausstellungswand aus Stoff

€358,95
3D-Wandbox-Ausstellungsdisplay aus Stoff

3D-Wandbox-Ausstellungsdisplay aus Stoff

€780,95
Individuell gestaltetes rundes Stoffhintergrund-Display

Individuell gestaltetes rundes Stoffhintergrund-Display

€301,95
Modulare EZ-Cubic-Textilturm-Ausstellung

Modulare EZ-Cubic-Textilturm-Ausstellung

€397,95
Modularer dreieckiger Stoffbanner-Displayständer

Modularer dreieckiger Stoffbanner-Displayständer

€207,95
Tragbares S-förmiges Stoff-Ausstellungsdisplay

Tragbares S-förmiges Stoff-Ausstellungsdisplay

€426,95
Tragbares Stoff-Ausstellungsdisplay mit geschwungenem Bogen

Tragbares Stoff-Ausstellungsdisplay mit geschwungenem Bogen

€245,95
Schlanke hinterleuchtete LED-Ausstellungswand aus Stoff

Schlanke hinterleuchtete LED-Ausstellungswand aus Stoff

€743,95
800+ Products available
50,000+ Orders
30+ Countries
22+ Years experience

Related Collections

Exhibition Transit & Carry Cases
Exhibition Transit & Carry Cases

Not sure which display fits your booth?

Get a free 2D mockup with your artwork — see exactly how it looks before you order. 7,000+ happy exhibitors.
Talk to an expert
Not sure which display fits your booth?

What our customers say

4.9from 7,200+ reviews
A great process from start to finish, good communication and the product arrived promptly and we are very happy with our banners! Thank you
Mikey WrightEvents Director, BluePeak
Amazing value, amazing product very accommodating too. Would recommend to anyone and everyone.
Josh NevilleEvents Director, BluePeak
Always a pleasure to work with Backdropsource! We've ordered several event banners through the company; they are always very helpful, fast, and the banners themselves are of great quality and easy to set up.
Miles StreetFounder, Trendline Co.
I ordered a teardrop banner for my Choir. Quick and efficient customer service, speedy delivery and top quality product!
ELAINE WEBBBrand Manager, NovaTech

Frequently Asked Questions

How does the fabric actually stay tight on the frame? +
Two mechanisms are used. A pillowcase graphic is a sewn sleeve pulled over the assembled frame and closed with a zip along the bottom or one side; the sleeve is deliberately cut slightly smaller than the frame, so putting it on stretches it. A silicone edge graphic has a strip sewn into the border that pushes into a groove in the extrusion, tensioning the print as each edge is seated. Neither relies on you pulling hard: if a skin needs real force, it is either the wrong size or the frame is not fully extended.
Why has my fabric wall started to sag or ripple? +
Work through the causes in order. First check every frame section is fully extended and locked, as a single joint short of home takes the tension out of a whole run. Second, check how the graphic was fitted: starting on one side and working across leaves the fabric off-square, whereas seating all four corners first and then the mid-points spreads the load evenly. Third, consider the skin itself, since polyester that has been repeatedly over-stretched at one corner will eventually hold that distortion permanently.
Should I print one side of the wall or both? +
Print both sides only when both sides are genuinely seen, such as an island stand or a wall standing in an open gangway. Where you do, the fabric needs an opaque or blockout construction, otherwise the reverse image ghosts through and both faces look muddy. On many stands the better answer is a printed front and a plain reverse in a brand colour, which costs less, looks deliberate, and avoids the alignment headache of getting two images to sit correctly on one sleeve.
What is different about the Slim Fabric LED Backlit Exhibition Wall? +
Backlit walls light the graphic from behind rather than washing it from the front, so the fabric must be translucent and the frame has to hold the LEDs far enough back for the light to even out before it reaches the print. That has consequences for the design: very dark, heavily inked areas block the light and can look patchy, while lighter tones glow. Backlit walls also need a power supply booked with the organiser, which is easy to forget when you are used to a passive fabric wall.
Square corners or rounded corners, which should I choose? +
Square-corner frames finish in a crisp right angle, which matters when the wall butts against another wall, sits in a corner plot or forms part of a run of panels, because a rounded edge next to a straight one shows as a gap. Rounded pillowcase corners are more forgiving of small fitting errors and give a softer look for events and photography. Decide by what the wall touches: anything joining another surface wants square corners.
Can I put a new graphic on a frame I already own? +
Usually, provided the new skin is made for that specific frame. Measure the frame itself rather than the old graphic, because a skin that has been in service for a while may have stretched and will give you a false reading. You also need to know which attachment system the frame uses, as a silicone edge graphic will not fit a pillowcase frame and vice versa. Photograph the frame profile and joints and send the images over if you are unsure which system you have.
How should the printed fabric be washed and stored? +
Wash cool with a mild detergent, no bleach and no fabric softener, then hang it to dry rather than tumbling it. A useful trick is to refit the graphic while it is very slightly damp, as the tension of the frame pulls the last creases out as it dries in place. Store it folded loosely in a bag of its own, away from heat and away from anything with a sharp edge, and vary the fold lines between shows so you never build a permanent crease in the same spot.
Which format works best on a corner or double-open stand? +
An L-Shaped Fabric Banner Display covers two sides of a corner plot from a single structure, so you get a continuous branded surface instead of two walls that never quite meet. A 180-degree curved wall wraps the back of an open stand and pulls people in from either side. Where visitors circulate around you, as they do in the wide gangways at somewhere like Farnborough International, a Modular EZ Cubic Fabric Tower or triangle module reads from every direction and takes up very little floor.